1. Remove the front under cover No.2. (See FRONT UNDER COVER No.2 REMOVAL/INSTALLATION.)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
| 1 | No.1 engine mount rubber |
| 2 | Bracket plate (No.1) |
| 3 | No.1 engine mount bracket |
| 4 | Bracket plate (No.2) |
1. Loosen the bolts shown in the figure.
NOTE:
The bracket plate (No.1) can move slightly by loosening the bolts shown in the figure and the No.1 engine mount rubber can be easily removed.
2. Remove the No.1 engine mount rubber.
1. Install the No.1 engine mount bracket, plate (No.1), and plate (No.2) and temporarily tighten the installation bolts.
2. Tighten the bolt shown in the figure.
Tightening torque
8—10 N·m {82—101 kgf·cm, 71—88 in·lbf}
3. Install the No.1 engine mount rubber and temporarily tighten the installation bolts.
4. Tighten the No.1 engine mount bracket, plate (No.1) and plate (No.2) installation bolts in the order shown in the figure.
Tightening torque
84—98 N·m {8.6—9.9 kgf·m, 62—72 ft·lbf}
5. Tighten the No.1 engine mount rubber installation bolts.
CAUTION:
Slots have been adopted for the No.3 engine mount installation holes. If the No.3 engine mount is deviated from the original position when installing the No.3 engine mount, engine noise or vibration could increase. Before removing the No.3 engine mount, place alignment marks on the No.3 engine mount and body so that they can be assembled to the same positions as before removal.
1. Remove the plug hole plate. (See PLUG HOLE PLATE REMOVAL/INSTALLATION [SKYACTIV-G 2.5].)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
| 1 | No.3 engine mount |
1. Remove the clips shown in the figure and set the ground cable aside.
2. Remove the front under cover No.2. (See FRONT UNDER COVER No.2 REMOVAL/INSTALLATION.)
CAUTION:
To prevent deformation of the oil pan, support the engine using the following methods.
When using an engine lifter, insert rubber of appropriate size (approx. 20 mm {0.79 in} thickness) between the engine lifter and the oil pan to support the oil pan.
When using a garage jack, place rubber of appropriate size (approx. 20 mm {0.79 in} thickness) on a batten which is large enough to cover the oil pan to support the oil pan.
3. Before removing the No.3 engine mount, support the engine (oil pan) using a commercially available engine lifter or garage jack.
4. Place alignment marks on the locations shown in the figure so that they can be assembled to the same positions as before removal.
NOTE:
Paint so that the No.3 engine mount is framed on the body side and the outline of the nut is framed on the No.3 engine mount side.
5. Remove the No.3 engine mount.
NOTE:
When replacing the No.3 engine mount, place a mark at the same position as the one placed before removal.
If the No.3 engine mount nut is loosened, tighten the engine front cover stud bolts because they may have loosened.
1. Tighten the engine front cover stud bolts.
Tightening torque
7—13 N·m {72—132 kgf·cm, 62—115 in·lbf}
2. Temporarily tighten the No.3 engine mount installation bolts and nuts using the following procedure:a. Align the alignment marks on the body side and No.3 engine mount, and temporarily tighten the bolts shown in the figure.
b. Temporarily tighten the nuts shown in the figure while aligning the alignment marks of the No.3 engine mount and nuts.
NOTE:
If the alignment marks are not aligned, align the alignment marks while slightly moving the engine and temporarily tighten the nuts.
3. Tighten the No.3 engine mount installation bolts and nuts in the order shown in the figure.Tightening torque
Installation position
Tightening torque
1
76—95 N·m {7.8—9.6 kgf·m, 57—70 ft·lbf}
2
82—95 N·m {8.4—9.6 kgf·m, 61—70 ft·lbf}
3
49—65 N·m {5.0—6.6 kgf·m, 37—47 ft·lbf}
4. Remove the engine lifter or garage jack.
5. Install in the reverse order of removal.
CAUTION:
Slots have been adopted for the No.4 engine mount bracket installation holes. If the No.4 engine mount bracket is deviated from the original position when installing the No.4 engine mount bracket, engine noise or vibration could increase. Before removing the No.4 engine mount bracket, place alignment marks on the No.4 engine mount bracket so that they can be assembled to the same positions as before removal.
1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.5].)
2. Remove the air cleaner, air hose and fresh air duct as a single unit. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-G 2.5].)
3. Remove the battery tray and PCM component. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.5].)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
| 1 | No.4 engine mount rubber |
| 2 | No.4 engine mount bracket |
1. Remove the clips shown in the figure and set the wiring harness protector aside.
2. Remove the front under cover No.2. (See FRONT UNDER COVER No.2 REMOVAL/INSTALLATION.)
CAUTION:
To prevent damage to the transaxle, support the transaxle using the following methods.
MTX: Support the clutch housing using a batten of appropriate size.
ATX: Place rubber of appropriate size (approx. 20 mm {0.79 in} thickness) on a batten which is large enough to cover and support the oil pan.
3. Before removing the No.4 engine mount rubber, support the transaxle using a commercially available engine lifter or garage jack.
4. Remove the No.4 engine mount rubber.
1. Remove the bolt shown in the figure and set the ground cable aside.
2. Place alignment marks on the locations shown in the figure so that they can be assembled to the same positions as before removal.
NOTE:
Paint so that the outline of the nut is framed on the bracket side.
3. Remove the No.4 engine mount bracket.
NOTE:
When replacing the No.4 engine mount bracket, place a mark at the same position as the one placed before removal.
If the No.4 engine mount bracket nut is loosened, tighten the transaxle stud bolts because they may have loosened.
1. Tighten the transaxle stud bolts.
Tightening torque
15—25 N·m {1.6—2.5 kgf·m, 12—18 ft·lbf}
2. Align the alignment marks on the No.4 engine mount bracket and nuts, and temporarily tighten the nuts shown in the figure.
3. Tighten the No.4 engine mount bracket installation nuts in the order shown in the figure.
Tightening torque
92—116 N·m {9.4—11 kgf·m, 68—85 ft·lbf}
4. Install the ground cable to the No.4 engine mount bracket.
Tightening torque
9—12 N·m {92—122 kgf·cm, 80—106 in·lbf}
1. Install the No.4 engine mount rubber and temporarily tighten the bolts and nut shown in the figure.
2. Tighten the No.4 engine mount rubber installation bolts and nut in the order shown in the figure.Tightening torque
Installation position
Tightening torque
1, 2
131—153 N·m {14—15 kgf·m, 97—112 ft·lbf}
3
54—62 N·m {5.6—6.3 kgf·m, 40—45 ft·lbf}
4
81—99 N·m {8.3—10 kgf·m, 60—73 ft·lbf}
3. Remove the engine lifter or garage jack.
4. Install in the reverse order of removal.