DTC P0054:00

HO2S heater resistance

DETECTION CONDITION

• The PCM monitors the HO2S heater resistance when under the HO2S heater control. If the resistance is more than 34 ohms, the PCM determines that there is a HO2S heater circuit problem.

Diagnostic support note

• This is an intermittent monitor (A/F sensor heater, HO2S heater).

• The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

• PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.

• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

• DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

• Stops fuel feedback control of HO2S

POSSIBLE CAUSE

• HO2S connector or terminals malfunction

• HO2S heater malfunction

• Short to ground or open circuit in HO2S heater power supply circuit

• Short to ground in wiring harness between ENGINE1 15 A fuse and HO2S terminal C

• ENGINE1 15 A fuse malfunction

• Open circuit in wiring harness between main relay terminal C and HO2S terminal C

• PCM connector or terminals malfunction

• Short to ground in wiring harness between HO2S terminal D and PCM terminal 2C

• Open circuit in wiring harness between HO2S terminal D and PCM terminal 2C

• PCM malfunction

STEP

INSPECTION

ACTION

1

• Have the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS (A/F sensor heater, HO2S heater related) been recorded?

Yes

Go to the next step.

No

Record the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.

2

• Verify related Service Bulletins and/or on-line repair information availability.

• Is any related repair information available?

Yes

Perform repair or diagnosis according to the available repair information.

• If the vehicle is not repaired, go to the next step.

No

Go to the next step.

3

• Switch the ignition off.

• Disconnect the HO2S connector.

• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 9.

No

Go to the next step.

4

• Inspect the HO2S heater.

  (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G 2.5].)

• Is there any malfunction?

Yes

Replace the HO2S, then go to Step 9.

(See HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [SKYACTIV-G 2.5].)

No

Go to the next step.

5

• Verify that the HO2S connector is disconnected.

• Switch the ignition ON (engine off).

• Measure the voltage at the HO2S terminal C (wiring harness-side).

• Is the voltage B+?

Yes

Go to the next step.

No

Inspect the ENGINE1 15 A fuse.

• If the fuse is blown out:

• Refer to the wiring diagram and verify whether or not there is a common connector between ENGINE1 15 A fuse and HO2S terminal C.

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has a short to ground.

• Replace the fuse.

• If the fuse is damaged:

• Replace the fuse.

• If the fuse is normal:

• Refer to the wiring diagram and verify whether or not there is a common connector between main relay terminal C and HO2S terminal C.

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has an open circuit.

Go to Step 9.

6

• Switch the ignition off.

• Disconnect the PCM connector.

• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 9.

No

Go to the next step.

7

• Verify that the HO2S and PCM connectors are disconnected.

• Inspect for continuity between HO2S terminal D (wiring harness-side) and body ground.

• Is there continuity?

Yes

Refer to the wiring diagram and verify whether or not there is a common connector between HO2S terminal D and PCM terminal 2C.

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has a short to ground.

Go to Step 9.

No

Go to the next step.

8

• Verify that the HO2S and PCM connectors are disconnected.

• Inspect for continuity between HO2S terminal D (wiring harness-side) and PCM terminal 2C (wiring harness-side).

• Is there continuity?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between HO2S terminal D and PCM terminal 2C.

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has an open circuit.

Go to the next step.

9

• Always reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

  (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.5].)

• Perform the KOER self test.

  (See KOEO/KOER SELF TEST [SKYACTIV-G 2.5].)

• Is the PENDING CODE for this DTC present?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the PCM.

  (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5].)

Go to the next step.

No

Go to the next step.

10

• Perform the “AFTER REPAIR PROCEDURE”.

  (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.5].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [SKYACTIV-G 2.5].)

No

DTC troubleshooting completed.