5

All power windows are inoperative

POSSIBLE CAUSE

• Power supply circuit or ground circuit malfunction

• Burnt fuse (IG1)

• Open or short circuit in wiring harness between ignition switch (IG1) and power window main switch

• Open or short circuit in wiring harness between power window main switch and power window subswitch

• Open or short circuit in wiring harness between power window main switch and power window motor

• Open or short circuit in wiring harness between power window main switch and ground

• Power window main switch malfunction (power cut-off switch malfunction, switch malfunction)

• Power window subswitch malfunction

• Power window motor malfunction

• Power window regulator malfunction

STEP

INSPECTION

ACTION

1

• Switch the ignition ON (engine off or on).

• Set the power cut-off switch to the UNLOCK (contact point: Close) position.

• Inspect the power window system operation again.

• Does the system operate properly?

Yes

System is now normal. (power cut-off switch is not set properly.)

No

Go to the next step.

2

• Operate all power windows other than driver’s window using the power window main switch.

• Does any power window operate?

Yes

Go to Step 6.

No

Go to the next step.

3

• Operate the driver’s power window using the power window main switch.

• Does the power window operate?

Yes

Go to the next step.

No

Inspect for an open circuit in the wiring harness between the power window main switch and the body ground.

Inspect the power window main switch connector connection. (damage/pulled-out pins, corrosion)

Repair or replace if necessary.

4

• Is the P.WINDOW1 30 A fuse normal?

Yes

Replace with the appropriate standard fuse.

If the fuse is melted, inspect the wiring harness for a short to ground. Repair or replace the wiring harness, then replace the fuse.

No

Go to the next step.

5

• Measure the voltage at the power window main switch terminal 1L.

• Is the voltage B+?

Yes

Replace the power window main switch.

(See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION.)

No

Inspect for an open or short circuit in the power window main switch wiring harness (battery power supply).

Inspect the power window main switch connector connection. (damage/pulled-out pins, corrosion)

Repair or replace if necessary.

6

• Identify the inoperative power window.

• Measure the voltage at the suspect power window motor (battery power supply) while operating the power window motor using the suspect power window subswitch.

• Is the voltage B+?

  (Open: terminal F/ close: terminal E)

Yes

Go to the next step.

No

Go to Step 9.

7

• Operate the power window using the power window subswitch.

• Does the power window motor operate (rotate)?

CAUTION:

• If the power window motor temperature is high, the motor may not rotate due to the motor internal bimetal function. Leave it untouched for about 3 min. to cool it down, then reinspect.

Yes

Go to the next step.

No

Replace the power window motor.

(See POWER WINDOW MOTOR REMOVAL/INSTALLATION.)

8

• Remove the door glass from the carrier plate.

• Make sure that the door glass moves smoothly using your hand.

• Does the door glass move smoothly?

Yes

Replace the power window regulator guide.

No

Inspect for a bent regulator guide or other possible malfunction. If normal, replace the glass run channel.

9

• Measure the voltage at the power window subswitch (power window motor output) while operating the power window subswitch.

• Is the voltage B+?

  (Open: terminal A/ close: terminal D)

Yes

Inspect for an open or short circuit in the wiring harness between the power window subswitch and power window motor.

Inspect the power window subswitch and power window motor connector connections. (damage/pulled-out pins, corrosion)

Repair or replace if necessary.

No

Go to the next step.

10

NOTE:

• Do not operate the power window subswitch during the following inspection.

• Inspect the continuity between power window subswitch terminal B (vehicle harness-side) and ground.

• Is there continuity?

Yes

Go to the next step.

No

Inspect for an open or short circuit in the power window subswitch wiring harness.

Inspect the power window subswitch connector connection. (damage/pulled-out pins, corrosion)

Repair or replace if necessary.

Then go to Step 12.

11

NOTE:

• Do not operate the power window subswitch during the following inspection.

• Inspect the continuity between power window subswitch terminal E and ground.

• Is there continuity?

Yes

Replace the power window subswitch.

(See POWER WINDOW SUBSWITCH REMOVAL/INSTALLATION.)

No

Inspect for an open or short circuit in the power window subswitch wiring harness.

Inspect the power window subswitch connector connection. (damage/pulled-out pins, corrosion)

Repair or replace if necessary.

Then go to Step 12.

12

NOTE:

• Do not operate the power window main switch during the following inspection.

• Inspect the continuity between power window main switch terminal (close; 1B,1A,1G) and ground.

• Is there continuity?

Yes

Go to the next step.

No

Replace the power window main switch.

(See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION.)

13

NOTE:

• Do not operate the power window main switch during the following inspection.

• Inspect the continuity between power window main switch terminal (open; 1D,1C,1I) and ground.

• Is there continuity?

Yes

Inspect for an open or short circuit in the wiring harness between the power window main switch and power window subswitch.

Inspect the power window main switch and subswitch connector connections. (damage/pulled-out pins, corrosion)

Repair or replace if necessary.

No

Replace the power window main switch.

(See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION.)