1

Door glass does not move up and down in automatic mode

POSSIBLE CAUSE

• Open circuit or short to power supply in sensor 1 signal, ground signal from wiring harness (between power window switch and power window motor), inner power window switch, or inner motor: Steps 4–7

• Open circuit or short to power supply/ground in sensor 2 signal from wiring harness (between power window switch and power window motor), inner power window switch, or inner motor: Steps 8–12

NOTE:

• The automatic function and the IG OFF timer function do not operate while the power window switch is in fail-safe mode. The fail-safe operates when sensor 1, and/or sensor 2, and/or the sensor power supply malfunctions.

• Sensor 1 and/or 2 malfunction

• When the door glass is moving up and down, the power window switch cannot sense a pulse signal from sensor 1 during the time it senses 5 pulses (2.5 cycles) from sensor 2.

• When the door glass is moving up and down, the switch cannot sense a pulse signal from sensor 2 during the time it senses 5 pulses (2.5 cycles) from sensor 1.

• There are three abnormal pulses in a pulse signal while the door glass is moving up or down.

• There are 20 cycle pulses from a closed position while the door glass is moving up.

• There is no pulse signal for 1 s after the door glass is moved down.

STEP

INSPECTION

ACTION

1

• Switch the ignition to off (LOCK) for 3 minutes.

• Switch the ignition ON (engine off or on).

• Initialize the power window system.

• Operate the auto open/close function.

• Does the power window operate properly?

Yes

System is normal.

The power window system auto open/close function does not operate temporarily for any of the following reasons:

• The power window switch is operated while the power window motor protection circuit (integrated in power window motor) is operating.

• The power window main switch power supply is cut off by disconnection of the negative battery cable or removing the fuse.

No

Go to the next step.

2

• Switch the ignition ON (engine off or on).

• Inspect the voltage at the following power window switch terminals (sensor 1 signal):

• Driver-side (at power window main switch): 2D

• Except driver-side (at suspected door’s power window subswitch): F

• Is the voltage approx.12 V when the door glass is moving up and down?

Yes

Go to step 7.

No

Go to the next step.

3

• Switch the ignition ON (engine off or on).

• Inspect the voltage at the following power window motor terminals B (sensor 1 signal):

• Is the voltage approx.12 V when the door glass is moving up and down in manual mode?

Yes

Go to the next step.

No

Replace the power window motor, then go to Step 12.

4

• Switch the ignition to off (LOCK).

• Disconnect the power window switch connector.

• Is there continuity between the following power window switch terminals (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch) and power window motor terminals?

• Driver-side:

• 2D–B (sensor 1 signal)

• 1A–D (sensor power supply)

• 1I–C (ground signal)

• Except driver-side:

• F–B (sensor 1 signal)

• J–D (sensor power supply)

• L–C (ground signal)

Yes

Go to the next step.

No

Repair the wiring harness between the power window switch and power window motor, then go to Step 12.

5

• Switch the ignition ON (engine off or on).

• Inspect the voltage at the following power window switch terminals (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch):

• Driver-side

• 2D (sensor 1 signal)

• 1I (ground signal)

• Except driver-side

• F (sensor 1 signal)

• L (ground signal)

• Is the voltage approx.12 V?

Yes

Repair the wiring harness between the power window switch and power window motor, then go to Step 11.

No

Replace the power window switch (open circuit or short to power supply in power window switch).

6

• Is there continuity between the following power window switch terminals (wiring harness-side) (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch) and ground?

• Driver-side

• 2D (sensor 1 signal)

• 1I (sensor power supply)

• Except driver-side

• F (sensor 1 signal)

• L (sensor power supply)

Yes

Replace the wiring harness between the power window switch and power window motor, then go to Step 12.

No

Go to the next step.

7

• Switch the ignition ON (engine off or on).

• Inspect the voltage at the following power window switch terminals (sensor 2 signal) (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch):

• Driver-side: 2F

• Except driver-side: D

• Is the voltage approx.6 V when the door glass is moving up and down?

Yes

Replace the power window switch (malfunction in power window switch automatic mode control), then go to Step 11.

No

Go to the next step.

8

• Switch the ignition ON (engine off or on).

• Inspect the voltage at power window motor terminal A (sensor 2 signal).

• Is the voltage approx.12 V when door glass is moving up and down?

Yes

Go to the next step.

No

Replace the power window motor, then go to Step 12.

9

• Switch the ignition to off (LOCK).

• Disconnect the power window switch connector and power window motor connector.

• Is there continuity between the following power window switch terminals (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch) and power window motor terminals?

• Driver-side: 2F and A (sensor 2 signal)

• Except driver-side: D and A (sensor 2 signal)

Yes

Go to the next step.

No

Repair the wiring harness between the power window switch and power window motor, then go to Step 12.

10

• Is there continuity between the following power window switch terminals (sensor 2 signal) (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch) and ground?

• Driver-side: 2F

• Except driver-side: D

Yes

Repair the wiring harness between the power window switch and power window motor, then go to Step 12.

No

Go to the next step.

11

• Switch the ignition ON (engine off or on).

• Measure the voltage at the following power window switch terminals (sensor 2 signal) (for driver’s door at power window main switch, for except driver’s door at suspected door’s power window subswitch):

• Driver-side: 2F

• Except driver-side: D

• Is the voltage approx. 12 V?

Yes

Repair the wiring harness between the power window switch and front driver-side power window motor, then go to the next step.

No

Replace the power window switch (open circuit or short to power supply/ground in power window switch), then go to the next step.

12

• Is malfunction no longer present?

Yes

• Troubleshooting completed.

• Explain repairs to the customer.

No

Reinspect malfunction symptoms, then repeat from Step 1 if malfunction recurs.